View Advertiser Index
|
Posted on 11/9/2007
|
Parts , Tools and misc for sale
Wiseco pistons,370ci (6021A3) 350 +030 domed piston uses a 6" rods and a 3.625 stroke $225
(New) TRW forged domed pistons. 360ci L2510/L2509 uses 6" rods and a 3.480 stroke crank. $400 last set left.
(New) Kieth Black hyperutectic flat top pistons, 358ci uses 6" rods and a 3.480 stroke $200
4340 forged crank, 3.500 stroke, $375
4340 BRC forged crank, 3.625 (3 5/8) stroke $600
GM forged crank, stroked to 3.550 small juornal $300 (SOLD)
400 block, prebored to 4.180, square decked and line bored with main studs. Has bottom 1" hard blocked. oil passages drilled, coolant passages opened up. With all the machine work done to this block it normally sells for $700. But it has some slight shadows that didnt clean in the cylinders. So I will sell it $400 wwhat the hell first $300
400 block,+ .040, pre bored to 4.160 decked and line bored. oil passages drilled (was) $500 first $400 takes it.
2-400 std bore blocks $200
305 blocks $25
triple disk clutch setup, used 1 season. not burnt up.$250
882 casting heads for sale, complete and ready to bolt on, new valves 1.94/1.5, surfaced, new springs,new guides, $200
991 heads, 2.02 int/1.6 exh. , new guides,pinned studs, new springs and locks, $3oo
487 heads, need seats $75
290 heads complete $250
461 heads angle milled not sure how much $50
991 head cores $50 pr.
882 head cores $25 pr.
292 turbo angle plug head, has been repaired, or i will buy a mate for this one.
Turbo 400 trans, used but good shape, $150
chevy 3 speed $100
Ford Parts
Ford 3 speed top loader $75
ford 4 speed top loader. ruff shape $100
Ford cleveland block and forged pistons, crank and rods, not assembled, heads also, $150
Ford 302 blocks, complete cores. $50
9" ford center sections $30
hobby stock manifolds $5pr
used imca tires $10
valve covers (tall) $8
corvette off set bolt finned valve covers $50
2 barrell intakes $25
4 barrell intakes $15
30 fan belts, $20 for all of them
Box full of new rings, some broken sets some complete sets, the whole box for $20 or $5 a set untill gone.
Extra seat grinding tools, pilots and stones and holders ,,,Ect,,, $200
Metal shop cabinets that hang on the wall, $100 each
Various sizes of heater hose (whole lot) for $30
buckets full of bolts (mostly motor bolts) $5 each
Big Block boring and hone plate, $150
Cam Bearing instalation tool, complete set with case $200
360 degree swivel lift hoist. comes with 2 different arms, $200
1 ton chain hoist $40
Chest type tool box full of tools for use at the track, $100
car ramps $5
Redi heater, uses kerosene, 40,000 btu, $100
small shop stool on wheels $10
creepers,$10
lawn chairs, $1 each
box of tie down straps and straping material, $20
metal conditioner $2 a bottle
Oil treatment, $2 a bottle
So any reasonable offer may be accepted on any of the stuff I have for sale.
[email protected] or call 712-289-2211 or 712-363-0996
Contact Information:
Terry Cohoon
Phone: (712)289-2211
Email: [email protected]
|
|
|
|
