View Advertiser Index
|
Posted on 6/23/2012 5:51:41 PM
|
lots 4 sale no junk, IMCA stock car 500 carb motor
IMCA stock car 500 carb motor. 360ci 4.060 scat rods, scat crank, stock appearing gated pan, 2 valve relief pistons 9.5 � 1 h140c pistons, balanced rotating assembly, new lw small balancer. 10.5 compression. Custom cam with edm oiling lifters. IMCA spec edelbrock alum intake, NEW comp cams full roller rockers, NEW never raced 487s milled to 65.5cc with all new ss valves, 1.94/1.6 valves, good springs, steel retainers and locks, screw in studs and guide plates, has lifter valley tray. The short block is used 8-10 nights in a hobby stock, ran with gibbs oil only. $3500 FIRM. This is the same build as the motor in my car.
14 inch alum air cleaner base with sure seal o ring. $10 each have two both offset style not centered.
14 inch alum steering wheel missing a few of the nubs off the back side. $25
4.75 bolt pattern Used Floater hubs complete with brgs, rotors and lug nuts. Used Ace\winters\prc brand. $200 pair
New 5 on 5 winters\prc hubs, complete with brgs, lug nuts, seals etc. NEW. $300 pair
60 inch centered floater housing. This has center less ground tubes for bolt on floating mounts etc�NEW $350
Axles all 31 spline. 28.5 solid, 29.5 gundrilled $75 each
Ultra shield full containment seat 16 inch. Like new. $400
RHS cast iron heads, CnC ported by Hvh and assembled by Jim Wyman, some hand port work in chambers around plugs. fereah hollow valves, 2.02/1.6. Isky springs, ten degree locks, retainers, screw in pro series 7/16 studs. $2000 complete dyno time only Due to rules changes. These are 1600 bare new from RHS.
13 inch 180 lb afco rear spring. $25
5.5x9.5 springs 975/1100 $10 each
New 15% reduction krc serpentine lower pulley R Lock. $20 shipped.
Used serpentine krc pulleys 3.5 lower and uppers. 1-1, 2 uppers, 3 lowers. R lock $10 each
Used Krc lower pulley and hub piece that mounts to the balancer. Serpentine. 3.5 not r lock older 2 pin style. $20 both pieces.
Crower ultra light 41# gun drilled mains and rods and seriously profiled throws! 434 crankshaft. Used. .010 400 mains, 2� st rods. Big block snout. Also have low nights Ati Balancer for this. Both $1000
Mahle flat top 434 pistons. 4.165 bore 1.00 pin height for 434,406 or 377 depending on rod length. NEW pistons with -5cc valve reliefs. New pins and locks included. $425
Cleaned and checked double hump head cores, bare. $25 each
Steering wheel quick release and part you weld to shaft. Button style. $10
7� bilstein shocks $75 each
3060 5555 1050 3050 2020 4555 4555 2060 3050 3050 new 3050 new dp1rf dp1lf
9� $75 each fx new means trailer worn new builds by fx suspension.
4010 5050 4040 4010 3010fxnew 3030fxnew 4010fxnew 1060fxtrailer worn 1090 2080 3080 4010fx 3020fx 4010fxnew
Contact Information:
Jeff, Mc Clelland,Ia
Phone: (712)310-1183
Email: [email protected]
|
|
|
|
