View Advertiser Index
|
Posted on 12/20/2011 7:54:24 AM
|
cage kart/dart,rhs,487x,383, 350 4 bolt
Go here for pics of for sale items..
http://s642.photobucket.com/albums/uu150/jnjfab/parts%20for%20sale/
Aluminum oem hoods with nice body lines, these are much stiffer after gutting than steel and are big so you can bow them as needed and cut them down. $125 each
66 racing T shirts white with 66 logo on front and back etc. $15 shipped to you.
Cleaned and painted machine grey metric spindles $60 each speedway gets $87.95!
Dirty metric spindles $40 each
Cleaned metric lower a arms with oem bushings ball joints $60
Dirty metric lower a arms with oem bushings ball joints $45
Cleaned metric lower a arms no ball joints or bushings $75
Stock vortec valve covers $10
New Mr gasket ultra seal cork/rubber vortec valve cover gaskets $5 pair have 2 sets
CNC ported RHS heads done by HvH open stock car or awesome modified heads�. all new parts best you can get. Chassis dyno time only on these heads. I sold the motor I had them built for. 61cc/ 219cc runners after CNC 2.02/1.6 valves. Fereah hollow stem valves, tool steel lw retainers, 1.5 $200 valve springs, ten degree locks. $2500 complete $1600 BARE
Dart 180cc 49cc Iron Eagle heads. Intake ports cleaned up and port matched some. Very good performance valve job. Heads are machined for vortec intake bolt pattern and old style. I used these to compare the spec IMCA vortec intake to the old style bolt pattern intake on the chassis dyno. FRESH straight from machine shop ready to bolt on. Manley race flo undercut lw valves, 10 degree locks and keepers. Springs are 140# and 340-360 open all test good and ready to run. $550
461 double hump heads, 2 nights since freshened with good perf valve job. Screw in studs, plates, big springs, stainless valves. READY to bolt on and go today. No porting. All good parts. $300
487x hobby stock legal heads, pulled off motor ran 15 nights. Screw in non shouldered studs. $450.00
350 4 bolt block .030 now needs honed to .040. $200.00
461 double hump head cores. $100 pair
462 double hump head cores $100 pair
NEW Pro/Race pro series race balancer, chrome, degree. SFI 18.1. NEW in package. ($229.99 from JR) Sell $100.00
Keith black .100 dome 383 pistons. 4.030 bore, on nice polished x rods, 4-6 nights old, childs albert moly rings. Nice package to put in your block. Balanced and with balance card. $250 all. This is rods, pistons and rings and balance card!!! Not a whole motor..
Quadra jet intake manifold. Modified plenum area thru 4- 3� holes gain of over 15 hp from weind 7547 proven on back to back dyno run by myself, no smoke and mirrors. $200 each. Pics on www.jnjfab.com in the for sale section.
Gm q jet intake manifolds. Un touched. #250 this is the cleanest oem casting available. Best flowing. $95 each
Roller tip rockers,1.5, 7/16 stud with tungsten balls for reduced heat! $70.00 complete set. 2 nights.
Roller rockers, red. 1.6 ratio 7/16 stud with locks, 1 night. $70
Roller tip rockers 7/16 stud, tungsten balls. 1 nights. 1.5-1.6 ratio. $70
New vortec cork and rubber valve cover gaskets. Awesome to glue to covers. $5 set
NEW never ran 400 harmonic balancer shelf worn only $10
400 oem crank $20
2 piece sbc timing cover, pan stays on and you can access timing chain to change cams etc. Like new dyno time only. $15 each have three
External balance plate for rear of crank for 400 or 383. $5 each have 3
sbc flat guide plates $5 a set have 4 sets
Plastic Howe carb storage tote!! $25 like new
Good Bilst shocks $65 each
7�4555, 1050, 2050, 4555, 3050, 3050,
9� 5030, 6020
NEW bilst trailer worn only $90 each
7� 5030, 3050
9� 4010
Wade Cross rebuilt Bilst NEW builds not even trailer worn $90 each
9� 6010, 6010, 5030, 4010
Wade Cross rebuilt used very little $75 each
7� 1060 high nitrogen pressure
9� 3010, 3010, 3020, 4010, 5030, 4010
swiveling 90 degree water neck with allen bolts $15
Metric caliper brake pad spacers $10 pair
Full size caliper spacers $10 pair
Carter fuel pump with -8 fittings welded in. $50 3 nights old
Holley fuel pump. Chrome. 12-327-11 is the part number. 110gph $70 used 3 nights
9" used short narrow yoke. $15 each
4.71 3rd member, lw spool, lw ring gear, 31 spline. $250
5.67 3rd member lw spool, lw ring gear. 31sp $500
5.00 3rd member lw spool, lw ring gear, 31sp $500
Front springs. 1150,1200, 1290 5.5x9.5 springs. Just rated. $20 each
Rear spring 5x13 Afco 180# $20
New 9� 3rd members $425 shipped to you in a storage tote. Mini spool up to 650 ratio. Add 75 for full lw spool, Add 100 for lw ring gear. Any yoke, any spline. Usually ships next day. Assembled with solid pinion spacer and shims, not crush collar. NEW NEW NEW NEW
New Gun drilled Axle. 31 spline. 29.5 long. $65.00 NEW
kids cage kart $1500
olympic brand adjustable front and rear suspension
extra sides
spare front and rear wheel and tire
almost every gear ratio sprocket goes with it
extra tie rods and heim joints for tie rods
toe gauges made by jnjfab
sells with toe gauges, air gauge, fire suit, $100 speedway gear bag, some lead, some tools, some oil.
$1500 all
Its red with red cage, body is in great shape needs nothing to go racing. was just scaled and caster camber set and parked.
EMAIL Jeff [email protected]
Contact Information:
Jeff, Mc Clelland,Ia
Phone: (712)310-1183
Email: [email protected]
|
|
|
|
